Skip to the content
Know your tech before you buy it. Makers: get listed from $49/mo

OpenELB

openelb.io

  • Free plan
  • Linux
  • Self-hosted
7.1 Club score Visit openelb.io

What OpenELB is

OpenELB exposes Kubernetes LoadBalancer services to external access in bare-metal, edge, and virtualization environments. It assigns service IP addresses from pools defined by Eip objects, and supports BGP, Layer 2, and VIP modes. BGP mode uses GoBGP to publish service routes to peer routers and supports ECMP; it requires a router that supports BGP and ECMP. Layer 2 mode requires infrastructure that allows anonymous ARP/NDP packets and forwards traffic through one active node, so failover can briefly interrupt services and bandwidth is limited to that node. VIP mode uses VRRP for high availability, but is limited to 255 VRRP instances per network and also has brief failover interruptions and a single-node bandwidth limit. OpenELB can be installed with kubectl manifests or Helm 3 and requires Kubernetes 1.15 or later. It currently supports IPv4 only. The project lists guides for Kubernetes, K3s, and KubeSphere and directs support questions to KubeSphere Slack. It is licensed under Apache License 2.0 and is a CNCF Sandbox Project.

Who it suits

OpenELB suits teams exposing Kubernetes services in bare-metal, edge, or virtualization environments. The appropriate mode depends on available router support and infrastructure requirements.

Good to know, and what to watch

  • Supports BGP, Layer 2, and VIP modes
  • Manages IP pools for service addresses
  • Installable with kubectl manifests or Helm 3
  • Guides cover Kubernetes, K3s, and KubeSphere
  • Supports IPv4 only
  • Requires Kubernetes 1.15 or later
  • Layer 2 and VIP have single-node bandwidth limits
  • BGP requires a router supporting BGP and ECMP

The verdict

OpenELB provides several ways to expose Kubernetes LoadBalancer services, with IP pool management and documented installation paths. Check the mode prerequisites and failover limits against your network before selecting a configuration.

What the maker publishes

Address family limit
The documentation says OpenELB currently supports only IPv4. source
BGP configuration
Users can configure BGP properties through BgpConf and BgpPeer custom resource definitions. source
BGP prerequisites
BGP mode requires a router that supports BGP and ECMP; the documentation recommends it for high availability without failover interruptions or bandwidth bottlenecks. source
Installation
OpenELB can be installed in a Kubernetes cluster using kubectl manifests or Helm 3. source
Integrations
The project lists installation guides for Kubernetes, K3s and KubeSphere. source
IP address pools
Eip objects provide address pools from which OpenELB assigns IP addresses to Kubernetes LoadBalancer services. source
IP management
It provides IP address pool management for service load-balancer IPs. source
Kubernetes requirement
Installation requires Kubernetes 1.15 or later because OpenELB requires CustomResourceDefinition v1. source
Layer 2 constraints
Layer 2 mode requires the infrastructure to allow anonymous ARP/NDP packets, and its traffic forwarding uses one node at a time, which can cause brief interruptions during failover and a single-node bandwidth bottleneck. source
Layer 2 limitations
Layer 2 mode forwards traffic through one active node, so failover briefly interrupts services and bandwidth is limited to that node. source
Layer 2 prerequisites
Layer 2 mode requires the infrastructure to allow anonymous ARP/NDP packets. source
License
OpenELB is licensed under Apache License 2.0. source
License
OpenELB is licensed under the Apache License, Version 2.0. source
Load balancing modes
OpenELB supports load balancing in BGP mode and Layer 2 mode, and its documentation also describes VIP mode. source
Load-balancing modes
It supports BGP mode and Layer 2 mode. source
Project origin
OpenELB is a KubeSphere sub-project; its repository says it was originally created by KubeSphere and is now vendor neutral and a CNCF Sandbox Project. source
Project status
The repository says OpenELB was originally created by KubeSphere and is a vendor-neutral CNCF Sandbox Project. source
Purpose
OpenELB exposes Kubernetes LoadBalancer services for external access in bare-metal, edge and virtualization environments. source
Purpose
OpenELB exposes Kubernetes LoadBalancer services to external access in bare-metal, edge, and virtualization environments. source
Router requirements
BGP mode requires a router that supports BGP and ECMP; the documentation suggests Layer 2 or VIP mode when those are unavailable. source
Routing
OpenELB supports ECMP routing and load balancing; its BGP mode uses GoBGP to publish service routes to peer routers. source
Routing
OpenELB supports ECMP routing and load balancing. source
Support
The project directs users to the KubeSphere Slack channel for support and discussion. source
Support
The project directs users to the KubeSphere Slack channel for support and discussion. source

Checked against the maker's pages on 4 Oct 2026.